潮州附近有没有服务

One station sandblasting manufacturer installation service

Sandblasting room | sandblasting machine | mechanical recovery automatic sandblasting room source strength manufacturers

Your location: homepage > Industry news >

National Service Hotline

thirteen billion four hundred and seventy-five million eight hundred and twenty thousand nine hundred and twenty-nine

Sandblasting machine: "features of environmental protection while spraying and suction sandblasting machine"!

The features of the environmental protection type side spraying and suction sand blasting machine are as follows: 1. Active recovery of abrasive, active separation, active circulation, no pollution; roughness target ra0.5-150um iso8503-1; surface treatment: cleanliness target sa2.5sa3iso8501-1

Sandblasting machine: "daily management of shot blasting machine"!

Daily operation of shot blasting machine. It is mainly to adjust the shot blasting current and reasonable allocation between the time. Electric current: how much control does the pill depend on in daily life. When the current of the sandblasting machine is low, it can be improved quickly, but when the current is high, it needs to slow down with the consumption of shot

Sandblasting machine: "effect of process parameters on workpiece sandblasting"?

Measurement of coverage rate of sandblasting machine: apply a layer of colored glaze or fluorescent glaze on the surface of the workpiece, and then sandblast the workpiece according to the process parameters. After sandblasting the workpiece surface once, take out the workpiece, and observe the share of residual coating on the surface under the microscope (magnifying glass)

Sandblasting machine: what do you know about the top ten maintenance methods?

1. Often add new sand, which must be cool and dry before adding new sand. 2. Parts over 10 tons in weight shall not be loaded into the sandblasting machine (parts with excessive weight and too long length shall not be sprayed). 3. The sand pit and sand storage chamber shall be completely cleaned every quarter. 4. The exhaust fan must be turned on when sandblasting

Sandblasting machine: "what should I do if the window glass is easy to blur?"

The window glass of sandblasting machine is easy to be ambiguous. What should be done? 1. The sandblasting operator should not face the sandblasting nozzle to the window glass, so as to avoid the sand material directly hitting the glass; 2. Some protective mould or transparent adhesive tape can be pasted on the inside of the window glass

Sandblasting machine: "what are some requirements for sandblasting room?"

The shot peening chamber body is made of light steel structure and sandwich color steel plate, and the structure is consolidated; the inner wall is lined with wear-resistant rubber protective plate, and both sides of the chamber body are equipped with safety doors. There are lighting lamps around the room to maintain sufficient brightness in the room. Shot peening machine and protective mask

Sandblasting machine: "what are the applications of liquid sandblasting technology?"

The use of liquid sand blasting technology 1. Finishing the rough surface of investment castings, using liquid sand blasting to finish the investment castings, can not only remove the oxide skin and residue on the surface of the casting, but also play a polishing effect and improve the surface finish of the casting. Especially for the shape of the complex no margin

There will be "blister like" sand blasting machine

Sometimes there is sand blasting or bubble like surface. Sandblasting machine produces this kind of phenomenon the reason mainly has the following several kinds: 1, the pigment in the paint material is too much or the particle is too thick. 2. The paint itself is not clean, mixed with impurities, and used without screening. 3. Deploy

Sandblasting machine: "the best treatment method of three metal surface coating!"

The recommended cleaning methods for uncoated galvanized steel are different due to different surface conditions. For new clean galvanized sheets, a simple solvent cleaning is sufficient to eliminate any protective oil used for field storage of galvanized sheets. other...

Sandblasting machine: "what devices are there in the pneumatic recovery sandblasting room?"

The pneumatic recovery sand blasting room is mainly composed of room body, sand blasting equipment, abrasive recovery equipment, ventilation and dust removal equipment, abrasive separation equipment and electrical control equipment. In order to simplify the equipment, sand blasting machine can merge the two parts of abrasive recovery and ventilation dust removal. Fan through bee

What are the simplest operation steps of sandblasting machine?

In the operation process of sandblasting machine, it can be generally divided into the following categories: 1. Turn on the power switch, the light is on, and do not leave the electric start. Don't leave the sand feeder. 2. Open the operation cabin, put the parts to be processed on the mesh plate, and close the door of the operation cabin

After the sandblasting machine is used in time, it is automatic

The appearance of the machine has indeed provided us with great help, but we can not only use them, but also have a good Bayan them together. In this way, we can confirm that the automatic sandblasting machine can be used for a longer time