潮州附近有没有服务

One station sandblasting manufacturer installation service

Sandblasting room | sandblasting machine | mechanical recovery automatic sandblasting room source strength manufacturers

National Service Hotline

thirteen billion four hundred and seventy-five million eight hundred and twenty thousand nine hundred and twenty-nine

Crawler shot blasting machine with loading and unloading

Author: admin Source: This station Time: 2015-12-30 10:47
This type of shot blasting machine is an alternative product of shot blasting cleaning drum, which has good cleaning effect and tight structure
The cleaning equipment with low noise and good integrity has the following characteristics:
[q3210] wear resistant rubber track reduces the collision and damage to the workpiece and reduces the
Noise.
The machine adopts q034 cantilever centrifugal shot blasting machine, which has the advantages of long service life, simple structure and fault
The rate is low;
The use of air separation separator has good separation effect and high productivity, which can improve the blade quality
Life span has a positive effect;
Using bag filter, the dust emission concentration is lower than the national standard, which improves the labor of workers
Environmental Science;
After the workpiece is cleaned, the crawler reverses to realize automatic unloading.
The upper unloading mechanism is adopted to further reduce the labor intensity of workers
Shot blasting is still the most economical and reliable cleaning method in the world. Shot blasting cleaning
Compared with other cleaning technologies, the technology has the following advantages:
Improve the fatigue resistance of mechanical products and metal components
Stress concentration relief
Prolonging its service life
Optimize the surface process state of workpiece
Improve cleaning efficiency
Reduce the labor intensity of cleaning work and reduce environmental pollution
working principle
In the cleaning chamber, the feeding mechanism is used to add no more than the specified number of workpieces. After the machine is started, the
At the same time, the high-speed projectiles thrown out by the shot blaster form projectile bundles, which strike evenly
On the surface of the workpiece, make it clean. After shot blasting and cleaning, the track can be reversed
The parts are discharged from the drum to the discharge mechanism, so the machine is particularly suitable for integration into the automatic production line.
The shot and sand particles are discharged through the small holes on the rubber track and flow into the steel mesh at the bottom for screening, and the screw is used for filtering
The rotary conveyor is fed into the elevator and separated in the separator. The dust is sucked by the fan to the dust collector
The clean air is discharged into the atmosphere, and the dust on the cloth bag falls into the bottom of the dust remover through the counter blowing rotary jet
In the dust collecting box, the user can remove it regularly, and the waste sand flows out of the waste pipe for reuse. Shot sand mixture
After the clean pellet is returned to the separator for use
The magnetic shot supply gate enters the shot blasting device and casts the workpiece again.
5.1 working procedure
Add projectile program
Pill 1
Turn on the hoist
Pill 2
Turn on the auger
Pill 3
Add new pellets to the slow equipment from the cleanroom door. These projectiles are transported and lifted by a screw conveyor
Finally, it is stored in the hopper at the lower part of the separator.
4 pills
Stop the auger, hoist and separator
Preparation procedure
Quasi 1
Operation of dust removal system
Quasi 2
Hoist on
Quasi 3
Auger on
Shot blasting cleaning
Throw 1
Lifting door, crawler forward rotation, feeding trolley ascending, hopper car tilting feeding, feeding trolley descending, lifting
The feeding door is closed when the door is lowered;
Throw 2
Open the shot blasting device and shot feeding gate, and start the cleaning work.
Throw 3
When the loading and unloading door of the crawler is completely reversed, the lifting mechanism stops
Lower and the feeding door is closed;
Throw 4
In case of emergency, press the emergency stop button and the machine will stop working immediately;
Shutdown Sequence
Off 1
Stop auger
Off 2
Stop the hoist
Off 3
Stop the separator
Off 4
Stop the dust remover and start the reverse jet motor for dust removal. After a certain period of time, the back blowing rotary jet is stopped. The whole machine works
stop it
be careful:
The dust in the dust collecting box under the dust collector should be removed regularly to prevent blocking the dust discharge pipe and affecting the dust removal efficiency
Fruit;
The bottom of the cleaning chamber and the debris under the screen in the separator funnel should be cleaned regularly;
The bullets around the equipment should be cleaned frequently to prevent slipping and injure people;
The crawler and elevator belt in the cleaning room should be checked regularly to avoid damaging the belt;
It is forbidden to open the feeding door when the shot blasting machine is not completely stopped to prevent accidents.

 

Technical parameters:

 
Technical parameters of q32 series shot blasting cleaning machine
              
type
project

Q326C

 

QR3210

Shot blasting machine productivity
T/h

0.6-1.2

 

1.5-2.5

Feed rate
kg

two hundred

 

six hundred

Maximum weight of single piece
kg

ten

 

thirty

End plate diameter
mm

¢650

 

¢1000

Effective volume
m

zero point one five

 

zero point three

Shot blasting quantity
kg/min

one hundred

 

two hundred and fifty

Dust removal air volume
m3/h

two thousand and two hundred

 

five thousand

Power consumption
kw

twelve point six

 

twenty-four point three

Dimensions
mm
3681×1650×5800   3972×2600×4768